Put the charging socket to socket shell under the slot. 2 of the ST3 * 8 fastening screws with electric screwdriver outlet cover to cover. The battery cover assembly to the battery card slot, the gaps between the black cable card to the card slot battery. Will the motor cover component is installed to the next, determine the motor installed in place. The connector straighten out, with tie together. Aim the main PCB button indicates the button hole of the lampshade, to be loaded on the indicator lamp shade, indicating lamp shade card buckle buckle PCB. Indicator card to indicate the lamp chamfer of the lampshade, lamp and lamp chamfer end face flush. The press of a button, the button is not on the PCB light switches is determined to resist. From cover to cover, button card card to the slot. On the cover to cover. Use the machine bottom up on tooling, electric screwdriver to five ST3 * 12 screw fastening cover under the machine screw hole. The dust cup on the machine. The blades under the flat side down on the ultrasonic tooling mould. Blades lid convex super, three holes on the blades of three fixed column on the blades. Hands start ultrasonic tooling, cover the blades fixed on the blades. Fixed blades of wind component. The dust cup set on ultrasonic tooling mould. Direction of the trademarks cover as shown on the dust cup cover a trademark of the slots. Hands start ultrasonic tooling, the trademarks cover is fixed on the dust cup. The dust cup components. Will the dust cup as shown in figure ways to ultrasonic tooling mould under fixed. Dust the dust cup mouth to mouth of the slots. Take film cover on the dust cup, hands start ultrasonic tooling, the dust cup mouth is fixed on the dust cup. Ultrasonic dust cup mouth of dust cup component. Will the dust cup as shown direction to a fixture on the fixed mould. Take the lions share of the front axle end once wheel through the plane of the end, turn the wheels to determine wheels rotate smoothly, and then the front axle of flat on the dust cup of shaft hole wear on the dust cup. Hands press tooling button and the wheel and axle pressure on the dust cup. Good pressure wheel dust cup components. The dustproof plug loaded on the dust cup of air inlet. Take after filter and filter elements in self-inspection. To filter components into 3.6 V after mesh seat, holding the filter elements are shown in direction of rotation, the filter elements within mesh card point card to card slot. After the components installed in the outside mesh screen. The filter elements into the dust cup. With clean flannelette machine clean dirt, grease and dust cup. The nameplate label to label the slots at the bottom of the machine. Take color tape folded 20 mm at one end, and then switch with color foam tape behind the machine switch button, as shown in protective bubble edge to switch from visual greater than 5 mm, with tape wrapped around a circle. The elevator cable tie fasten to the round hole elevator. The elevator cable tie to the handle of the machine. Will the machine in a plastic bag (note: the bottom of the elevator on the machine). The conical bubble such as graphic method is to use a fixed color tape in the paper. Will the machine of the dust cup up, according to the shape into the paper holder (the bottom of the elevator on the machine). Will on the paper according to the shape at the top of dust to dust cup take color box shipping mark on the color with this graphic box, color box again into graphic shapes according to the crease and fold as shown at the bottom of the order. Russian pamphlets, brochures, warranty card, such as graphic way. Next to put the manual way of components as shown in figure in the whole machine, and then from top to bottom color box set on the machine. Take manuals, warranty CARDS, Russian pamphlets fold together, as seen here attach the carton (as shown), then the color box installed from top to bottom. On the cover on the color box, paper buckle buckle to the hole. Put the color box in electronic weighing on said, make sure no packing or more accessories. The carton according to crease fold into graphic shapes. The bottom of the carton with tape to seal a word way. The six color box outside to inside of the machine, the direction of the color box. On the cover on the carton, use tape to seal a word way. The carton of neatly put on the pallet.